Technische Spezifikationen
SPL
125 dB
Verstärkerleistung
2 X 750 W Bass (Class D) + 400 W Midrange (Class D) + 250 W Treble (Class D)
Frequenzgang
29 Hz - 21 kHz ("-6 dB")
Genauigkeit des Frequenzgangs
± 2 dB (34 Hz - 20 kHz)
Treiberabmessungen
2 x ⌀ 305 mm Bass + ⌀ 125 mm Midrange + ⌀ 25 mm Treble (Anzeige in Inch)
Abmessungen
H 489 x W 1210 x D 412 mm, (Anzeige in Inch)
Gewicht
79.5 kg / 175.3 lb
Anschlüsse
1 x XLR Analog Input
1 x XLR AES/EBU Input
1 x XLR AES/EBU Output
2 x RJ45 Control
1234AC SAM™ Studio Monitor
SAM™ Studio Monitor
Technische Spezifikationen
Der 1234AC ist ein SAM Hauptmonitor für den Einsatz in der anspruchsvollen Film- und Postproduktion, wo perforierte Leinwände oder hochauflösende LED-Displays verwendet werden.
Systemspezifikationen
Frequenzgang
34 Hz - 20 kHz (± 2 dB)
Low cutoff -6dB
29 Hz
High cutoff -6dB
21 kHz
SPL
Peak SPL Maximum peak acoustic output per pair in a listening room with music material at 2 m.
≥130 dB
Kurzzeitiger max. SPL Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
≥125 dB
Max. Langzeit-SPL Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver protection circuit) at 1 m.
≥120 dB
Eigenrauschen
Eigenrauschen Self generated noise level in free space at 2 m on axis (A-weighted).
≤0 dB SPL
Gewicht
Gewicht79.5 kg (175.3 lb)
Abmessungen
Höhe
489 mm
Breite
1210 mm
Tiefe
412 mm
Gehäuse
Gehäusematerial
MDF
Gehäusetyp
Reflex port
Treiber
Treiber-Typ
Cone
2 x 305mm (12 in) cone
Anzahl
2
Durchmesser
305 mm
Treiber-Typ
Cone
125mm (5in) cone.
Durchmesser
125 mm
Treiber-Typ
Metal dome
25mm (1 in) metal dome.
Durchmesser
25 mm
Richtwirkung
Harmonische Verzerrung
> 200 Hz ≤0.5 %
Gruppen-Laufzeit
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF
5.2 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
Abschnitt Verstärker
Verstärker
2 x 750 W Class D
3U rack mounted external amplifier.
Höhe
132 mm
Breite
483 mm
Tiefe
286 mm
Gewicht
11.2 kg
(24.7 lb)
400 W Class D
3U rack mounted amplifier.
Höhe
132 mm
Breite
483 mm
Tiefe
286 mm
Gewicht
11.2 kg
(24.7 lb)
250 W Class D
3U rack mounted amplifier.
Höhe
132 mm
Breite
483 mm
Tiefe
286 mm
Gewicht
11.2 kg
(24.7 lb)
Netzspannung
100-240 VAC 50/60Hz
Stromverbrauch
ISS aktiv
≤6 W
Leerlauf
≤40 W
Volle Leistung
2500 W
Abschnitt Signalverarbeitung
Anschlüsse
Input Analog signal input connector XLR female, balanced 10 kOhm.
Input Digital signal input connector XLR female 110 Ohm.
Output Digital signal output / Thru connector XLR male 110 Ohm.
2 x Control Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.
Crossover
Bass/Mid
420 Hz
Mid/Treble
3168 Hz