Technische Spezifikationen
SPL
121 dB
Verstärkerleistung
500 W Bass (Class D) + 250 W Midrange (Class D) + 200 W Treble (Class AB)
Frequenzgang
30 Hz - 22 kHz ("-6 dB")
Genauigkeit des Frequenzgangs
± 2.5 dB (35 Hz - 20 kHz)
Treiberabmessungen
⌀ 385 mm Bass + ⌀ 125 mm Midrange + ⌀ 25 mm Treble (Anzeige in Inch)
Abmessungen
H 810 x W 480 x D 420 mm, (Anzeige in Inch)
Gewicht
57 kg / 125.7 lb
Anschlüsse
1 x XLR Analog Input
1 x XLR AES/EBU Input
1 x XLR AES/EBU Output
2 x RJ45 Control
1238A SAM™ Studio Monitor
SAM™ Studio Monitor
Technische Spezifikationen
Der 1238A ist unser größter Monitor mit drei Treibern. Er passt sich an Ihre Raumakustik an und liefert Präzision auf Referenzniveau auch bei hohen Schalldruckpegeln.
Systemspezifikationen
Frequenzgang
35 Hz - 20 kHz (± 2.5 dB)
Low cutoff -6dB
30 Hz
High cutoff -6dB
22 kHz
SPL
Peak SPL Maximum peak acoustic output per pair in a listening room with music material at 2 m.
≥124 dB
Kurzzeitiger max. SPL Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
≥121 dB
Max. Langzeit-SPL Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver unit protection circuit) at 1 m.
≥116 dB
Eigenrauschen
Eigenrauschen Self generated noise level in free field at 1 m on axis (A-weighted).
≤10 dB SPL
Gewicht
Gewicht57 kg (125.7 lb)
Abmessungen
Höhe
810 mm
Breite
480 mm
Tiefe
420 mm
Gehäuse
Gehäusematerial
MDF
Gehäusetyp
Reflex port
Treiber
Treiber-Typ
Cone
385mm (15 in) cone
Durchmesser
385 mm
Treiber-Typ
Cone
125 mm (5 in) cone
Durchmesser
125 mm
Treiber-Typ
Metal dome
25mm (1 in) metal dome
Durchmesser
25 mm
Richtwirkung
Harmonische Verzerrung
> 200 Hz ≤0.5 %
Gruppen-Laufzeit
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF
5.1 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
Abschnitt Verstärker
Verstärker
500 W Class D
Höhe
132 mm
Breite
483 mm
Tiefe
252 mm
Gewicht
6 kg
(13.2 lb)
250 W Class D
200 W Class AB
Netzspannung
100-240 VAC 50/60Hz
Stromverbrauch
ISS aktiv
≤0.5 W
Leerlauf
≤25 W
Volle Leistung
750 W
Abschnitt Signalverarbeitung
Anschlüsse
Input Analog signal input connector XLR female, balanced 10 kOhm.
Input Digital signal input connector XLR female 110 Ohm.
Output Digital signal output / Thru connector XLR male 110 Ohm.
2 x Control Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.